Exsenco - Products

GYcRP


		As for the GYcRP probe, it can obtain analog output by combining with the GYFC2 controller.The GYFC2 controller has warning function usually, monitors cable broken wire and magnetic falling off. In addition output of speed is possible, in addition to position output, by the differentiating circuit inside (option).The GYFC2 controller was the succession type of type GYFC controller until recently, while compatibility could be given in installation size external size was miniaturized.Of course, there is no modification in output specification and the connector, the GYFC controller and is easily replacement use possible.

Specifications

		GYcRP/GYFC2
Precision	Linearity	Below TYP ±0.05%FS
	Resolution	Below 0.01%FS
	Repeatability	Below ±0.01%FS
	Temperature characteristic	Below 0.005mm/℃+10ppmFS/℃ (probe)
	Temperature characteristic	±20ppmFS/℃ (controller)
Output	Voltage output	0 - 10VDC or 10 - 0VDC Load current max 5mA load resistance min 2kΩ
	Electric current output	4 - 20mA or 20 - 4mA load resistance max 500Ω
	Alarm output	Dry b contact point 1A 30VDC
	Speed output	±10V (speed resolution 1%FS) (option)
Scanning frequency		It differs 1kHz (by effective stroke)
Power source and consumed electric current		+24VDC type +24V±5% below 350mA ±15VDC type +15V±5% below 200mA 　　　　　　　　 -15V±5% below 100mA +12VDC type +12V±5% below 700mA
Environmental characteristic	Resisting pressure	35MPa (probe rod)
	Category temperature range	-5℃ - +65℃ (probe) 0℃ - +60℃ (controller)
	Storage temperature range	-40 - +85℃
	Resistance swing	6G (or 40Hz 2mmPP)
	Shock resistant	50G (2msec)
	Protective standard	IP65 (probe)
Cable		1.5m (standard) (Max200m)

* The above-mentioned precision is applied to the sensor above effective stroke 300mm.
- It can produce the effective stroke of the probe at the optional length of 30mm - 7500mm.
- The cable the optional length to 200m is possible. When (it exceeds 200m, please consult. )
- As for output fine control of zero/full scale points it is possible to do with the controller front trimmer. (Adjustment range: ±3%FS)

Type Variations

Effective stroke

300,500,700,1000,1500,2000

Installation screw

M: M24×P1 (standard) N: M18×P1.5 U: 3/4-16UNF

Cable removal

CN: Connector type (standard) G*: [piguteiru] type (* cable length [m]: Standard 1.5)

Probe type

Sign	Probe type	Sign	Probe type
RP	GYcRP	FS	GYFRS
RS	GYcRS
R4	GYMR4
R5	GYMR5

Effective stroke (mm)

You follow largest effective stroke probe specification.

Basis dead zone size (mm)

You follow basis dead zone size probe specification.

Position output

Sign	Output 1 (OUT1) [Z] - [F]	Output 2 (OUT2) [Z] - [F]
A	0 - 10V	10 - 0V
BD	0 - 10V	4 - 20mA
BR	10 - 0V	20 - 4mA
CB□□: Bipolar output	- □□ - +□□V	+□□ - - □□V
VD [Z]/[F] (Example) VD1/5 (Example) VD0.5/9.5	Designated value voltage 1 - 5V 0.5 - 9.5V	It does not output
VR [Z]/[F] (Example) VD9.5/0.5	It does not output	Designated value voltage 9.5V - 0.5V
I [Z]/[F] (Example) I20/5.38	It does not output	Designated value electric current 20.00 - 5.38mA

* [Z] = zero points (basis) output [F] = full scale point (point) output

Supply power supply voltage

Sign	Supply power supply voltage
24S	+24VDC (standard)
15W	±15VDC
12S	+12VDC

Magnetic or float form

Sign	Magnetic type	Sign	Float type
M0	No.0	F28S	φ28SUS316
M0SM	No.0SPM	F30S	φ30SUS316L
M0LM	No.0LPM	F40S	φ40SUS316(B)
M2P	No.2P	F42S	φ42.5 sphere SUS316
M2PN	No.2PN	F50S	φ50SUS316
M3	No.3	F54S	φ54SUS304
M11	No.11	F25N	RF-A10 plastic float
M11N	No.11N	F28N	RF-A6 plastic float
T142	No.T14-M2	FL□	Float other than describing
T144	No.T14-M4
T162	No.T16-M2
T163	No.T16-M3
MG□	Magnet other than describing

The option sign (in case of non entry there is no option)

V []: Speed output, [] maximum path velocity (mm/sec) enters inside.

External Dimension Drawing


	●GYcRP probe

	Material probe head: Aluminum alloy 　　　Probe rod: SUS304

				<[piguteiru] type (option)>
	●GYFC2 controller

Options

[piguteirupurobu]
　In order to designate the size of axial direction of the sensor probe head as the compact, replacing to the connector, it is the option which uses the cable gland.
SRT (Shock Resistant Technology)
　It is the series which obtains the signal stability under shocking approximately 800G which you can use for also the application where the vibration and shocking condition are harsh. (It is not something which guarantees the life when the impact of 800G operates continually. )
Subaqueous use type probe
　When includes the sensor head section and makes the whole sensor submerge, the sensor head, in combination with the cable to purpose, specification it is the option which is modified.
GYEC-21DIN rail installation type analog controller
　You can use the GYcRP probe combining with the GYEC-21 controller of DIN rail installation type.